Shifter base for Tremec Magnum aftermarket – forward shift conversion For Sale
- Estimated Delivery : Up to 4 business days
- Free Shipping & Returns : On all orders over $200
- Shortcut to fulcrum chart
- (TUET11009, TUET11010, TUET11011, TUET11012, TUET16884, TUET16885)
- GM Performance # 19352208 19329795 19301620 ( T56 Super Magnum )
- Ford #Â M-7003-M6266 &Â M-7003-M6295
-
- Kit includes shifter base for forward location & 6-bolt cover plate for tail location
- Drop-in, direct fit for Magnum in situations where tail base is too far rearward
-
-
Does NOT FIT other T56 or TR6060 models – see separate listings
- IF your tail base does not have a 6-bolt mount, do not buy this – see other listings
-
- Only fits at forward location; see separate listings for tail bases
- Mounts on a rectangular 4-bolt pattern that is ~ 2.88 wide x 3.65 long; stub pivot ball center is ~1.5 below the flange
-
- Wait until new transmission is installed to buy shifter parts
- Remove existing shifter base if present
- Sit in vehicle, in driving position, with all interior trim (dash, console, etc) in place
-
-
Define desired knob location in space (neutral position):
- Measure height from base flange to desired knob location = overall height
- Measure side & rear offsets from receptacle bore to desired knob location
- See this diagram for clarification
- Study the Hurst stick page for shapes that meet your needs
- Allow 3-6 for stick mount height
- Choose a stick and see what fulcrum heights are compatible with it (see chart)
- Check overall height (see chart: stick height + mount height = overall height)
- Confirm chosen combination achieves desired knob location and that fulcrum height works with stick length selected
- Consider various stick & stub combinations to optimize
- Note long sticks on angled mounts will strongly offset knob to left (can be 5-6 +)
- Options E & F require a Hurst stick directly mounted on side w serrations
-
- Stick length = point-to-point distance from mount hole to knob thread
- Stick mount height = distance from base flange to stick bolt hole (affects knob height)
- Fulcrum height = distance from lower ball to fulcrum pin; varies by option, not published
- Warning: Follow stick length guide to avoid excess effort & component failure
-
- Billet steel gear selector stub
- Hardened steel cross-pin & stainless steel fulcrum pivot ring
- Self-centering cross-gate bias springs with heat treated spring seats
- Glass-reinforced polyamide fulcrum socket with steel wear clips
- Extruded aluminum housing with Spirolox steel support ring
- Zinc-plated laser-cut steel base-plate & cover
- Rubber oil control seal with steel retaining ring
- Vibration-resistant serrated flange head steel retaining bolts
-
Choose a fulcrum height (see chart down page first): [A] for use w/ 8" stick, [B] for use w/ 10"+ stick – short mount, [C] for use w/ 10"+ stick – tall mount, [D] for use w/ 12"+ stick – angled mount, [E] for use w/ 13"+ stick – angled mount – Hurst sticks only!!, [F] for use w/ 14"+ stick – angled mount – Hurst sticks only!!, [I] for use w/ 6" stick
Related products
Review Cart
Shifter base for Tremec Magnum aftermarket – forward shift conversion For Sale$99.50Select optionsShifter base for Tremec Magnum aftermarket – forward shift conversion For Sale$99.50Select options
Kit includes mounting hardware and instructions. Compare to Hurst #3918309. The base is built by Core Shifters using proven components inside a custom housing:
Stub fulcrum height options (critical to optimizing leverage for short throw):
Option For stick length stick mount height stick mount angle upcharge A 8 2.8 vertical default B 10 3.3 vertical +$10 C 10 + 4.3 vertical +$20 D 12 + 5.1 angled 14 deg left +$30 E 13 + 4.0 angled 14 deg left +$40 F 14 + 4.2 angled 14 deg left +$40 I 6 3.3 vertical +$80 - Stick length = point-to-point distance from mount hole to knob thread
-
Define desired knob location in space (neutral position):
A Hurst stick is required (NOT included, sold separately). Other brands and homemade sticks are discouraged. Stick mount has 3 8 -24 threaded holes spaced 7 8 apart on center + mating serrations for a Hurst stick on one face. Due to larger mounting threads (3 8 -24), sticks that use 8mm mounting bolts (most OE, non-TKO Lokar, others) will not work. Lokar TKO sticks can be mounted but only to the smooth side of the stub. To select the proper parts:
- Wait until new transmission is installed to buy shifter parts
-
Does NOT FIT other T56 or TR6060 models – see separate listings
- Kit includes shifter base for forward location & 6-bolt cover plate for tail location
Core Shifters forward shift conversion kit for AFTERMARKETÂ Tremec Magnum 6 speed:
